Free brake inspection can detect wear, leaks
Q I keep hearing this advertisement on the radio about a place offering a free brake inspection. Can you please explain what they'd check on my brakes and how I'd know that I'm being sold the correct things? I don't know anything about brakes, so let's keep it simple.
— Georgia Renson
A No problem! Your car, unless it's a classic, has disc brakes in the front, and either drum or disc brakes in the rear.
Disc brakes use a clamping device called a caliper to press brake pads against the brake rotor. There is an inner and outer pad, and they contain friction material on the side pressing against the rotor.
Disc pads somewhat resemble an elongated, double-stuffed Oreo cookie, with one outer piece removed. The filling is the friction material, and the cookie part is the metal backing. Pads must be renewed when the friction material wears thin, or the metal backing will damage the rotor's smooth surface.
Brake pads may last 25,000 to 75,000 miles, depending on driving habits, vehicle type and friction material composition. Pads that stop the best typically create more dust and don't last very long, and long-lasting pads are often noisy and don't stop as well. Try for the middle.
Calipers are operated by hydraulic force, via brake fluid, which is sent under very high pressure from the master cylinder as you apply the brake pedal. Calipers rarely leak or bind as long as the brake fluid is renewed every four or five years. The master cylinder, located in the upper-left-rear corner of the engine compartment, utilizes a fluid reservoir, which needs to be checked periodically for proper fill level. In the very rare case of master cylinder problems/leakage, it's usually internal, and causes a sinking brake pedal.
Brake rotors are dinner plate-sized metal discs located just behind your wheels. They may last the life of the vehicle but can wear thin, become warped from brake overuse or be damaged by worn pads. If a car or truck stops smoothly, with no pedal pulsation or squeaking, the rotors are probably OK, although they should be checked for adequate thickness. Rotors that have worn too thin don't dissipate heat properly and must be replaced. I'm not a fan of machining rotors unless called for by noticeable symptoms.
Rear drum brakes contain a wheel cylinder, brake shoes, springs and shoe-holding hardware, and the brake drum. Typically, the brake shoes should be renewed when the friction material wears thin. You might also need to machine the drums, which restores roundness and surface finish, and renew hardware and possibly the wheel cylinder if it's leaking. I'd avoid machining the drums if the vehicle slows smoothly with the parking brake applied. Wheel cylinders and hardware often last the life of the vehicle.
The definition of a brake inspection can vary widely, and a free one may be accompanied by higher-than-normal sales pressure. Typically it may be a visual inspection of the above parts, a measurement of rotor or drum thickness, a check for an illuminated ABS light or codes, and a road test. Fluid may also be tested for contamination with a test strip.
Brad Bergholdt is an automotive technology instructor at Evergreen Valley College in San Jose, Calif. Readers may send him email at firstname.lastname@example.org; he cannot make personal replies.
Show commenting policy
TribLive commenting policy
You are solely responsible for your comments and by using TribLive.com you agree to our Terms of Service.
We moderate comments. Our goal is to provide substantive commentary for a general readership. By screening submissions, we provide a space where readers can share intelligent and informed commentary that enhances the quality of our news and information.
While most comments will be posted if they are on-topic and not abusive, moderating decisions are subjective. We will make them as carefully and consistently as we can. Because of the volume of reader comments, we cannot review individual moderation decisions with readers.
We value thoughtful comments representing a range of views that make their point quickly and politely. We make an effort to protect discussions from repeated comments either by the same reader or different readers.
We follow the same standards for taste as the daily newspaper. A few things we won't tolerate: personal attacks, obscenity, vulgarity, profanity (including expletives and letters followed by dashes), commercial promotion, impersonations, incoherence, proselytizing and SHOUTING. Don't include URLs to Web sites.
We do not edit comments. They are either approved or deleted. We reserve the right to edit a comment that is quoted or excerpted in an article. In this case, we may fix spelling and punctuation.
We welcome strong opinions and criticism of our work, but we don't want comments to become bogged down with discussions of our policies and we will moderate accordingly.
We appreciate it when readers and people quoted in articles or blog posts point out errors of fact or emphasis and will investigate all assertions. But these suggestions should be sent via e-mail. To avoid distracting other readers, we won't publish comments that suggest a correction. Instead, corrections will be made in a blog post or in an article.