Muzzleloader season right around the corner
TribLIVE Sports Videos
Mornings are crisp and cool, the sun is rising a bit later every day, and tree leaves are beginning to show just a hint of fall color. Officially, it's autumn and the fall muzzleloading rifle season is about three weeks away. If you have an antlerless deer tag, a muzzleloader stamp on your 2008-09 hunting license and, of course, a "smokepole," you're all set.
While there is a trend followed by some toward modern "in-line" muzzleloaders, flintlock ignition rifles shooting patched roundballs are still preferred by a good number of black powder shooters who value tradition and true "primitive weapon" hunting. I call them the "purists."
So for newcomers to the "purist" muzzleloader ranks, properly loading a flintlock and shooting patched roundball ammo can be a bit of an enigma. One of the most frequent questions about muzzleloading shooting is how to load for optimum accuracy.
Roundball ammo is not noted for exceptional accuracy; nevertheless, when shooting at ranges of 100 yards or less, excellent field accuracy can be achieved with roundball fodder. The degree of accuracy, however, depends on at least a half dozen factors.
First and foremost is the rate of twist in the barrel. While modern in-lines designed to shoot conical bullets have a fast rate of twist, around one turn in 28 inches (1:28) or thereabouts, the best roundball accuracy is obtained from barrels having a rate of twist ranging from 1:60 to 1:72. Considering the latter, 1:72 means the rifling in the barrel will make one complete turn every 72 inches. Therefore, in a typical 28-inch barrel the rifling would make just a bit more than one-third of a full turn.
Many off-the-shelf rifles sold today have a compromise twist, 1:48, ostensibly to shoot both roundball and conical projectiles with an acceptable degree of accuracy for either. Keep in mind, the best accuracy for patched roundball shooting is obtained with slow rates of twist such as 1:60 to 1:72. However, rifles with a 1:48 twist shouldn't be discounted as viable and reliable hunting arms. We say that because of other factors that contribute to good accuracy. If you have a rifle with a 1:48 twist barrel, there's no need to run out and buy a new gun.
Accuracy is also contingent on the size of the roundball and, perhaps more importantly, patch thickness. In .50 caliber rifles (by far the most common flintlock caliber) two roundball sizes are used -- .490 and .495. Personally, I tend to shy away from the .495 simply because after two or three shots, despite a quick scrubbing, the bore becomes fouled, making running a larger size ball down the bore more difficult.
A .50 caliber rifle may have grooves cut .015 deep, essentially giving a maximum groove to groove diameter of .530. Of course, exact depth of grooves and width of lands in barrels may vary slightly depending on the manufacturer.
Basically, if we shoot a .490 roundball in a .50 caliber barrel, we need a .020 thick patch to "fill in the gap." The exact patch thickness that gives the best accuracy, however, can range from .015 to .020. Proper thickness is best determined by what works best, and that means doing a lot of careful range shooting. A patch of proper thickness will help keep the bore cleaner as well as yield better accuracy.
Visually inspecting fired patches is a good way to determine if the patch thickness being used is right for a particular rifle. Fired patches are usually found 15 to 25 feet or so from the muzzle after firing. If the patch is burned through, either the patch material is too thin or it was not lubed sufficiently.
Some fraying around the edges is to be expected; however, badly frayed patches may indicate that the patch is too thick. (Another possibility is that the fraying is caused by a rough bore, however, that is not a likely possibility. In extreme cases, a rough bore can be lapped though rough bores will gradually become smoother with more shooting).
It was mentioned that burned patches may be an indication of insufficient application of patch lube. Patch lube performs multiple duties. One, it makes running the patched roundball down the bore easier. Two, a sufficient amount of lube will prevent hot gasses from burning the patch material. It also cuts down on friction therefore giving a slightly higher velocity.
A good patch lube also helps suspend black powder fouling in the bore making cleaning easier. I guess the old-time mountain men weren't too fussy and used old-fashioned and readily available spit as a patch lube, but that's one tradition on which I'll pass. Spit just won't do the job that commerical lubes will.
A variety of patch lubes are available on the market. Shooters may also buy pre-lubed patches. If pre-lubed patches are not allowed to sit around for a while, they work fine.
Show commenting policy
TribLive commenting policy
You are solely responsible for your comments and by using TribLive.com you agree to our Terms of Service.
We moderate comments. Our goal is to provide substantive commentary for a general readership. By screening submissions, we provide a space where readers can share intelligent and informed commentary that enhances the quality of our news and information.
While most comments will be posted if they are on-topic and not abusive, moderating decisions are subjective. We will make them as carefully and consistently as we can. Because of the volume of reader comments, we cannot review individual moderation decisions with readers.
We value thoughtful comments representing a range of views that make their point quickly and politely. We make an effort to protect discussions from repeated comments either by the same reader or different readers.
We follow the same standards for taste as the daily newspaper. A few things we won't tolerate: personal attacks, obscenity, vulgarity, profanity (including expletives and letters followed by dashes), commercial promotion, impersonations, incoherence, proselytizing and SHOUTING. Don't include URLs to Web sites.
We do not edit comments. They are either approved or deleted. We reserve the right to edit a comment that is quoted or excerpted in an article. In this case, we may fix spelling and punctuation.
We welcome strong opinions and criticism of our work, but we don't want comments to become bogged down with discussions of our policies and we will moderate accordingly.
We appreciate it when readers and people quoted in articles or blog posts point out errors of fact or emphasis and will investigate all assertions. But these suggestions should be sent via e-mail. To avoid distracting other readers, we won't publish comments that suggest a correction. Instead, corrections will be made in a blog post or in an article.
- Steelers’ Harrison eyes stretch run
- Starkey: Artie Rowell’s incredible odyssey
- Penguins co-owner Lemieux snuffs rumored rift with Crosby
- Steelers notebook: Tomlin ends practice with third-down work
- Emotional send-off awaits Pitt seniors
- Michigan State takes bumpy road to finale against Penn State
- House fire displaces family of 6 in Somerset County
- HS highlight reel: Pair of title games to be on tape delay Saturday
- Gorman: Thomas Jefferson quarterback Kelley savors run after injuries, illness
- Palestinian artist who appealed blasphemy sentence of 800 lashes, prison sentenced to execution
- Seneca Valley football team hopes to improve in offseason